泥状鉱石の前処理方法はどのように選択すればよいですか?トロンメルスクラバー、丸太洗浄機、ハイドロサイクロンクラスター間の境界の定義。
The equipment list for the pretreatment of clay-bearing ores cannot simply be assumed to consist of one unit each of a drum washer, a trough washer, and a hydrocyclone. Even when ore material is "sticky," the nature of the problem varies: in some cases, loose soil merely adheres to the surface; in others, ore particles are encased in tough, cohesive clay lumps; and in still others, the clay has already dispersed and entered the slurry stream destined for downstream separation. Each scenario requires a different solution, necessitating a different configuration and quantity of equipment. Before selecting equipment, one must determine which material components should be retained and which should be discarded, while also assessing the required intensity of clay-disintegration (scrubbing) and the specific particle-size separation criteria. Otherwise, one might end up cleaning the surfaces of coarse ore particles only to lose valuable fine particles into the waste stream; conversely, if clay lumps remain intact during the initial stage, downstream processes might be forced to compensate through excessive pressure or increased water addition. The "clay content" (percentage of mud) is only one aspect and cannot, by itself, dictate the choice of equipment. Representative ore samples must preserve the original proportions of clay lumps, coarse fragments, and fine material, allowing for the observation of how they behave when wetted and agitated. Clay that breaks apart easily cannot be treated with the same approach as "plastic" clay-material that remains malleable when wet and re-agglomerates when kneaded. Furthermore, naturally loose fine particles are not the same as clay minerals. When selecting equipment, it is essential to distinguish between "clay lumps that have not yet disintegrated" and "fine clay that has already dispersed" before deciding whether to employ scrubbing or hydrocyclone-based desliming. The former requires an assessment of mechanical action, while the latter focuses on the separation of specific fine-particle fractions. While both issues may coexist, they cannot be addressed by the same methods. Once clay lumps have been broken down, the various particle-size fractions-including the washed-out fines-should be sampled and analyzed to determine the distribution of valuable minerals. If the valuable components are concentrated in the fine fraction, the objective should be to recover these fines and remove the barren coarse fragments, rather than simply maximizing the removal of "mud." If hard, cemented aggregates prove too resistant to be broken down by scrubbing, alternative approaches-such as crushing or other pretreatment methods-must be evaluated; simply increasing the duration of the scrubbing process is not a universal solution.
ドラム式鉱石洗浄機を評価する場合、主に考慮すべき点は、タンブリング動作によって粘土コーティング (覆われた泥) を効果的に破壊できるかどうかです。これらの機械は、ドラム内の材料の転がり、持ち上げ、落下と水の作用を利用して、表面の付着物を取り除きます。容易に分散可能な粘土コーティングを含む原料や、より粗い部分を含むさまざまな粒径の混合物を含む原料の場合、ドラム式洗浄プロセスを検討することが現実的な選択肢となります。洗浄用に設計されたこの装置を、分級 (スクリーニング) のみを目的とした単純な回転スクリーン (トロンメル) と区別することが重要です。性能を評価するには、洗浄後の粗粒子に粘土残留物が残っているかどうかに注目し、排出された微粉が完全に凝集物から解放されていることを確認します。吐出スラリーが薄くなったということは、単に水と固体の比率が変化したことを示しているだけです。さらに、外側では丸く見える粘土の塊でも、内部に閉じ込められた鉱石粒子がまだ含まれている可能性があります。非常に靭性の高い粘土やプラスチック粘土を使用する場合、ドラム内で単純に転がすだけでは完全な分散が保証されない可能性があります。実際、材料によっては丸まって圧縮された泥団子になる場合もあります。このような状況では、単にドラムのサイズを増やしたり、水の量を増やしたりするだけでは必ずしも解決策にはなりません。代わりに、過剰な摩耗によって引き起こされる貴重な鉱物の潜在的な過剰粉砕 (粉砕) を監視しながら、さまざまな処理方法によるテスト結果を比較してください。ドラム直径、有効洗浄長、内部構成、材料滞留時間などのパラメータは、特定の鉱石サンプルに基づいて決定する必要があります。統合された排出スクリーニングセクションを含むモデルの場合、洗浄とスクリーニングの両方の能力を個別に評価する必要があります。ユニット全体の定格スループットが、洗浄段階とスクリーニング段階の両方の要件を同時に満たすと仮定することはできません。

「トラフ式選鉱機」という用語には、さまざまな構造設計の装置が含まれます。この説明では、特に、頑固な粘土コーティングを施した鉱石を処理するために強力な材料間スクラビングを利用するデュアルシャフトパドルを備えたユニットに焦点を当てます。このカテゴリには、標準のスパイラルサンドワッシャーまたはスパイラル分級機は含まれません。粘土コーティングの除去が難しい頑丈な粗粒鉱石を扱う場合、このタイプのトラフベースの装置は比較試験を考慮する必要があります。デュアルシャフトパドルは材料の反転と相互摩耗を促進します。ただし、このプロセスの有効性は、最大供給サイズ、粒度分布、トラフ内の滞留時間、粘土の特定の特性などの要因によって左右されます。機器の選択は実際のパドル構成に基づいて行う必要があり、あるメーカーのモデルの許容される供給仕様パラメータを単純に別のメーカーのモデルに適用することはできません。集中的なスクラブの目的は粘土コーティングを除去することであり、保存すべき鉱物粒子をさらに粉砕することではありません。砕けやすい鉱石、高割合の微粉、または貴重な細粒鉱物を含む飼料の場合、微粒子スラリー生成の増加と微粒子の潜在的な損失を監視することが不可欠です。粘土が除去しにくいからといって、むやみにスクラブの強度を上げてはいけません。さらに、トラフから排出されるスラリーには専用の管理計画が必要です。特定の微粒子画分を事前に分離するかどうかは、鉱石サンプルの組成、スクラビング効率、および貴重な成分の分布によって決定する必要があります。分離された微細物質にさらなる処理が必要な場合は、プロセスフローチャート上で「廃スラリー」としてラベルを付けるべきではありません。

液体サイクロン クラスターは、鉱物スラリーの分類を担当します。供給されたスラリーを流体場を利用して処理し、粒子をオーバーフロー流とアンダーフロー流に分配します。一般的に、分級、脱スライム、または微粒子の回収に使用されます。ブレードや羽根車などの機械的洗浄コンポーネントを備えた装置とは異なり、液体サイクロンは頑固な未確認の粘土凝集体を効果的に分解することができません。供給物中の過大な粒子、異物、未遊離の凝集物は、選択した液体サイクロンの特定の供給要件に従って、事前に管理する必要があります。液体サイクロンは、すでに分散している粒子を分散させることはできますが、必ずしもすべての粘土凝集体をばらばらにすることはできませんし、オーバーフローの流れが自動的に廃汚泥だけになるわけでもありません。サイズや密度などの粒子の特性と動作条件が分布に影響します。分類結果は、絶対的なスクリーンのようなカットオフではありません。貴重な微粒子はオーバーフローに報告される可能性がありますが、アンダーフローには微細な粘土が含まれる可能性があります。どちらの製品ストリームも評価が必要です。液体サイクロン クラスターは通常、スラリーの総流量を複数のユニットに分散するように構成され、冗長性のために追加の容量が提供されます。機器の選択には、ユニットの寸法、動作ユニットの数、ポンプサンプとポンプの仕様、スラリー配管、供給濃度、動作圧力を総合的に検討する必要があります。単にコーンの数を数えるだけでは不十分です。さらに、特定の操作圧力に達しても粘土骨材の崩壊が保証されるわけではなく、事前の試験なしに普遍的な脱スライムのカットオフ点を定義することは不可能です。運用評価は、フィード、オーバーフロー、アンダーフローのサンプルを同時に収集し、安定した同等の条件下で実施する必要があります。粒度分布に加えて、乾燥固形分含有量と貴重な成分の分布を分析することが不可欠です。オーバーフローに報告される貴重な微粒子については、後続の水処理プロセスを計画する前に回収戦略を確立する必要があります。








